Acyclism

This results in an alternation of positive torques (the engine provides mechanical work, supplied by combustion) and negative torques (the engine consumes mechanical work, used for compression).

It is the average of these torques that characterises the torque provided by the engine to move the vehicle forward.

This alternation of torque generates acyclism, which results in a non-uniform rotational speed.

The speed is the superposition of two components:

  • A uniform mean speed
  • A pulsating speed

Mean speed, pulsating speed, acyclic speed

Mean speed, pulsating speed, acyclic speed

THE PROBLEM OF ACYCLISM

Although filtered by the flywheel, acyclism propagates to the drivetrain (clutch, gearbox, transmission) as well as to the accessories driven by the engine (alternator, air-conditioning compressor, vacuum pump, belts, etc.).

It generates vibro-acoustic phenomena that are harmful both to user comfort and to the equipment subjected to them (accelerated ageing, degradation of performance or functional characteristics).

Today, due to increased performance and efficiency, lighter equipment and a growing concern for reliability, manufacturers increasingly take acyclism into account in their specifications, both for equipment design and for testing.

This type of test gives the manufacturer the means to:

  • Characterise the performance of the equipment
  • Verify the reliability of the equipment and quantify its service life through endurance tests

What parameters define acyclism?

Acyclism is defined by:

The amplitude, expressed as a % of the mean speed, or converted into angular acceleration (rad/s²). This is the amplitude of the pulsating speed ωp as shown on the graph above.

The harmonic: the number of sinusoidal pulsation oscillations per crankshaft revolution.

Acyclism can be single- or multi-harmonic.

The phase, between the acyclic pulsation and an angular reference of the crankshaft, generally top dead centre (TDC).

How is acyclism generated?

To simulate the acyclism of an engine on a test bench, three methods can be used:

Mechanical acyclism generation: a shaft with universal joints is used, set so that the joint angle generates a sinusoidal speed ratio of harmonic 2 between the two ends of the shaft.

Strengths Weaknesses
  • Simple to implement
  • Low cost
  • Only harmonic 2 can be generated
  • Limited speed
  • Bulky
  • Constant but non-adjustable phase
  • Electrical acyclism generation: an electric motor combined with a servo drive is used. Generation is achieved through the analogue speed setpoint signal.
Strengths Weaknesses
  • Simple to implement
  • Low cost
  • Great flexibility of use
  • Multi-harmonic capability
  • Adjustable phase
  • Limited acyclism amplitude
  • Limited torque
  • Hydraulic acyclism generation: a rotary hydraulic actuator is used to add an angular oscillation to the uniform mean-speed rotation provided by an electric motor.
Strengths Weaknesses
  • Very high dynamic torque
  • Great flexibility of use
  • Multi-harmonic capability
  • Adjustable phase
  • High cost
  • Complex implementation
  • Limited by the hydraulic bandwidth

NERYS SOLUTIONS (Hardware and Software)

NERYS offers turnkey solutions for the design and construction of test facilities incorporating acyclism generation.

These solutions make it possible to subject a sample to an acyclism environment identical to the one it encounters when fitted on the vehicle.

The solutions offered by NERYS make it possible to:

  • Measure acyclism (amplitude and phase of each harmonic studied), using specifically developed measurement and signal processing methods
  • Generate and control acyclism, in closed loop, in amplitude and phase, for each harmonic studied.

These solutions rely on the acquisition and generation hardware of our partner NATIONAL INSTRUMENTS, as well as on our VASCO software product developed in LabVIEW.

The platforms used for measuring and generating acyclism are:

  • PXI-RT
  • CompactRIO
  • Real-time PC

Whether for generation, measurement or analysis, NERYS implements the latest software and acquisition/generation hardware solutions.

NERYS advises you in the choice of motors and drives to achieve the highest acyclism performance. We build complete test benches including:

  • Mechanics
  • Electrical engineering
  • Motor and drive
  • Control cabinet
  • Control platform (PXI, PC or CompactRIO)
  • Control software

THE OFF-THE-SHELF (COTS) SOLUTION: VEGA

Building on its experience on specific projects, NERYS has created an off-the-shelf product that covers all the acyclism needs of industrial companies. The idea is that the IT part and the control cabinet are completely standard, in order to offer a validated, functional technical solution requiring minimal commissioning, while keeping costs and lead times under control. As an option, several motor + drive sets can be chosen to have a complete drive chain to integrate on a test bench.

  1480 Avenue d'Arménie
Pôle d'Activités Yvon Morandat
13120 Gardanne

  ZA du Héron
597  route des Bons Prés
73110 La Croix-de-la-Rochette

Conception de moyen d'essais

Your tests partner

Mesulog